FORMBRIM FIELD NOTES / DESIGN GUIDE

Pom pom beanie sample approval

Use one identified sample to check the crown attachment with the pom on and off. Record the receiver and backing together, then use the two views to decide which part needs a revision before bulk.

View this design
Spruce-green knit beanie with a ribbed fold-over cuff and a centered sandstone yarn pom
Design reference · final fit, material and finish are agreed through sampling.
FOR BRAND & SOURCING TEAMS3 MIN READ4 PRACTICAL NOTES
NOTE 01

Set the crown and fitting reference

Record the sample ID, crown knit, folded cuff depth and fit reference. Mark center front and back on the sample record, and use the same fitting position for each observation. Take front and side views with the pom removed so you have a starting profile for the crown. Note the pom diameter and reference weight beside the hardware and backing references.

Label the detached pom with the sample ID and photograph its base. This keeps the two fastener halves paired with the same record during comparison. Agree what the buyer expects to see with the pom fitted and with the receiver exposed. Record the folded cuff and opening measurements separately from the crown assembly.

NOTE 02

Inspect the receiver with the pom removed

Look at the empty receiver from above and from the side. Check where it sits relative to the marked center and note any puckering around its edge. Turn the crown over and identify the backing patch by its outline. Inspect how its edge meets the knit and check the area the wearer may feel when the hat sits in the agreed position.

Photograph both sides of the attachment and label the views with the sample ID. Record the backing material, outline and attachment method separately from the snap. If there is a visible ridge, mark whether it follows the backing edge, the receiver or a nearby knit join.

Spruce crown and rib knit swatches with a sandstone yarn pom and a round backing patch
MATERIAL DISCUSSIONSpruce knit / sandstone yarn pom

Knit and attachment references · record the crown, cuff, pom and backing separately before reviewing the assembled sample

NOTE 03

Compare the same hat in both states

Attach the recorded pom and seat the beanie in the same position. Compare its centerline and crown profile with the first views. Note whether the pom leans, shifts during ordinary handling or pulls a section of knit upward. Remove the pom, return the hat to the same position and check whether the surrounding knit returns to the recorded profile.

If you need two prototypes, keep the crown, cuff, pom and receiver the same and compare one backing change at a time. Repeat the attached and detached observations on both. Record any additional changes the sample maker needed so they can be considered when choosing the next revision.

NOTE 04

Decide what needs a revision

Suppose the crown sits evenly with the pom removed, but one side lifts when the pom is attached. Mark the lifted area and check the alignment of the two fastener halves before requesting a crown change. If the two halves align and the patch edge creates a ridge inside, request a backing revision and repeat the fit check with both configurations.

Keep the accepted crown, cuff, pom, receiver and backing references with the approved sample. Include photographs of the two configurations and specify how the pom should be packed with the hat. Carry the signed revision, label requirements and quantities per finished colorway into the bulk brief. The bulk minimum is 300 pieces per style, per color.

Rear of the spruce-green beanie with the pom removed and the crown snap exposed
THE REFERENCE VIEWRear & profile

Compare the rear crown shape with the pom removed.

Inspect the physical sample before approval.
YOUR COLLECTION / OUR NEXT CONVERSATION

Turn the notes into a brief.

Bring your planned order breakdown, schedule questions and chosen design. Leave any undecided details open for discussion.

Project brief
Spruce-green knit beanie with a ribbed fold-over cuff and a centered sandstone yarn pomCobalt and ivory embroidery thread spools
FORMBRIMPom pom beanieOEM / ODM

Bring your shape, artwork and quantities together.

YOUR NEXT CONVERSATION
  1. Style-and-color breakdown
  2. Questions from your guide
  3. Target date and destination
MOQ
300 pieces per style, per color
Sample
7–10 working days
Production
30–45 working days

Prefer a direct conversation?

WhatsApp +86 181 2050 6050 ↗[email protected]

Fields marked * are required. Other details can be decided together.

Include + and your country code, followed by your WhatsApp number.
Add project details (optional)Style, quantities, timing & links
MOQ: 300 pieces per style, per color. List different styles and color quantities in your project description.
Share an http(s) link to your artwork or tech pack and check that we can open it.
PDF, JPG or PNG. Up to 3 files, 5 MB each and 10 MB total. To send files through WhatsApp, attach them in that chat.
Continue on WhatsApp

Your filled-in details will open in WhatsApp. Review them there before sending.