FORMBRIM FIELD NOTES / DESIGN GUIDE

Gathered bonnet sample approval

Review the gathered bonnet as one assembled sample. Establish which crown, band and tie references are accepted before requesting a change to any one of them.

View this design
Dark aubergine bonnet with a gathered crown, separate smooth band and two flat side ties
Design reference · final fit, material and finish are agreed through sampling.
FOR BRAND & SOURCING TEAMS3 MIN READ4 PRACTICAL NOTES
NOTE 01

Set the baseline for crown volume

Start with the sample ID and pattern revision. Mark center front, center back and both sides on a crown-to-band photograph. With the band in its agreed position on the fit reference, record where crown depth is measured and how the crown is supported. Use the same setup when comparing the next sample. A flattened crown and a supported crown give different readings.

Compare the amount and distribution of fullness in each marked section with the accepted drawing. Note a concentrated group of gathers by location and check whether the adjacent band edge follows the intended line. If the overall crown depth is acceptable, record it separately so a request to redistribute gathers can retain the accepted depth.

NOTE 02

Inspect the opening and both tie roots

Use the agreed method to check the finished opening at the smooth band. Record the fit reference and how the ties are set. Compare both band edges from front and rear. If a section turns over during the review, mark where it starts and record the position of the nearest tie root. Review the band in that position before deciding which component to revise.

Lay each flat tie out without pulling it. Measure from its sewn root to the finished tip and mark the two roots separately. Turn the bonnet inside out to inspect the band join beside each root and check whether the tie lies flat as it leaves the band. Photograph the left and right attachments on the same sample and identify any exposed edge, twist or bulky join by side.

Aubergine fabric swatch beside a gathered crown and band seam sample with a stitched cloth tie
MATERIAL DISCUSSIONAubergine cloth proposal

Bonnet development reference · review the proposed cloth, gather join and tie attachment on the same sample

NOTE 03

Review the mark on the assembled band

Compare the finished-size artwork with the mark on the sample and measure from the named band edge. Check the relationship to the gathered seam and the nearest tie root with the band at the recorded setting. Inspect the inside attachment and label position together. Record artwork, label and fabric references separately so any proposed substitution is visible in the next review.

If the band is approved before decoration, keep a photograph of its accepted edge and shape. Compare the decorated sample against that reference. When the mark shifts toward a gather or root, ask for an identified artwork placement revision and check the band again before carrying its approval forward.

NOTE 04

Close one gather revision

Suppose the opening, crown depth and tie attachments are accepted, but fullness bunches just behind the left tie root. Mark that sector on the inside and outside views and request a redistribution along the crown-to-band seam. Retain the approved band opening, crown depth and tie roots. Ask the sample maker to identify any neighboring gather sectors that also need to change.

On the next sample, use the same fit setup to compare that section and both adjacent sectors. Recheck the band edge near the root, then record each item as accepted, revise or pending. File the approved sample ID with the cloth, artwork and finished colorway quantities. Confirm the packing arrangement and size allocation separately when preparing the bulk handoff.

Rear of the dark aubergine bonnet with gathers meeting the smooth band
THE REFERENCE VIEWRear & profile

Follow the gather distribution across the rear crown and into the separate band.

Inspect the physical sample before approval.
YOUR COLLECTION / OUR NEXT CONVERSATION

Turn the notes into a brief.

Bring your planned order breakdown, schedule questions and chosen design. Leave any undecided details open for discussion.

Project brief
Aubergine bonnet with a gathered crown, smooth band and cloth tiesCobalt and ivory embroidery thread spools
FORMBRIMSleep bonnetOEM / ODM

Bring your shape, artwork and quantities together.

YOUR NEXT CONVERSATION
  1. Style-and-color breakdown
  2. Questions from your guide
  3. Target date and destination
MOQ
300 pieces per style, per color
Sample
7–10 working days
Production
30–45 working days

Prefer a direct conversation?

WhatsApp +86 181 2050 6050 ↗[email protected]

Fields marked * are required. Other details can be decided together.

Include + and your country code, followed by your WhatsApp number.
Add project details (optional)Style, quantities, timing & links
MOQ: 300 pieces per style, per color. List different styles and color quantities in your project description.
Share an http(s) link to your artwork or tech pack and check that we can open it.
PDF, JPG or PNG. Up to 3 files, 5 MB each and 10 MB total. To send files through WhatsApp, attach them in that chat.
Continue on WhatsApp

Your filled-in details will open in WhatsApp. Review them there before sending.